Home/Floor standing speakers /Floor standing speakers ELAC FS 507 VX-JET
Advertise

Photos and specs Floor standing speakers ELAC FS 507 VX-JET

Review and test Floor standing speakers ELAC FS 507 VX-JET
  • Floor standing speakers ELAC FS 507 VX-JET
  • Floor standing speakers ELAC FS 507 VX-JET
  • Floor standing speakers ELAC FS 507 VX-JET
  • Floor standing speakers ELAC FS 507 VX-JET

Description floor acoustic ELAC FS 507 VX-JET


This is a 3.5-way model refers to the 500-th reference line, conceding superiority to the elder sister FS 509 VX-JET.


The column has an elegant varnish finish and impeccable build quality. Perfectly damped enclosure has a plurality of struts and ties to provide stability to vibration and resonances. Because of this, each speaker got its own office.


In ELAC FS 507 VX-JET uses an innovative retractable coaxial MF/HF driver VX-JET made on the basis of the X-JET and consisting of the famous ribbon tweeter placed in the centre midrange speaker with a membrane AS-XR, which is a sandwich of paper and aluminum. The entire MF/HF module can be extended (due to suspension) at 8 mm above the front surface and utaplivajutsja at the same depth. This changes the chart its direction. The driver is driven via the back side of the special column adjusting handle. This know-how allows you to benefit from the combination of acoustics with almost any room. It is recommended to use recessed inside the speaker if the room has many reflective surfaces, and extended to the outside, if the room has a lot of sound-absorbing objects.


For the LF section is responsible 180 mm pair of woofers. Their diffuser AS-XR is a paper cone, stuck a thin layer of aluminum with a specially stamped surface, resembling the surface of the crystal. In this case the voice coil is connected with the base paper and aluminium membrane. As a result, the diffusers get additional rigidity and lack of resonance oscillations, while ensuring accurate, undistorted sound. All speakers this speakers have cast aluminum baskets.


Between the body column and its base there is a gap, since the reflex port is at the bottom of the Cabinet. The base features a massive adjustable spikes. At the rear of the speaker are two pairs of screw terminals, i.e., a column can be connected by biwiring scheme or use beninghove connection. The crossover uses air coils and film capacitors. The front part is closed by the acoustic grill, which is fixed with magnets.


Thanks to innovative technology ELAC FS 507 VX-JET will feel great even in rooms with difficult acoustic conditions. Napolenic provides a smooth, large-scale and detailed sound with precise tonal balance, deep bass and detailed treble.


Features floor acoustic ELAC FS 507 VX-JET



Retractable coaxial MF/HF driver VX-JET
Two 180-mm woofer with diffusers AS-XR (Crystal Membrane)
Upper limit frequency response up to 50 kHz


Features of outdoor acoustics ELAC FS 507 VX-JET

The number of bands3,5
The number of speakers3
Housing typebass reflex port is pointing down
MF/HF-emitterretractable combo coaxial MF/HF driver VX-JET (1x50/105 mm ring radiator, the air diffuser AS-XR, Crystal Membrane) in the center of the JET tweeter is installed
Low-frequency transducer2 x 180 mm, with diffusers AS-XR (Crystal Membrane)
Frequency range26 – 50000 Hz
Nominal impedance4 Ohms
The minimum impedance3.5 Ohms (95 Hz)
Sensitivity88,5 dB (2,83 V, 1 m)
The frequency bands180/550/2700 Hz
Recommended amplifier power rating will60-500 watts per channel
Nominal/peak power220/300 watts
Input connectorstwo pairs of screw terminals
Dimensions (WxHxD)280х1198х413 mm
Weight37 kg

Advertise
Copyright © 2013-2024 audio-reviews.com